Hit The Order Button To Order A **Custom Paper**

>> CLICK HERE TO ORDER 100% ORIGINAL PAPERS FROM AustralianExpertWriters.com <<

12 Mar
2020

MP4706 Sensors, Instrumentation & Control | Good Grade Guarantee!

1 of4UNIVERSITY OF CENTRAL LANCASHIRESCHOOL OF ENGINEERINGASSESSMENT 1MODULE CODE: MP4706MODULE TITLE: Sensors, Instrumentation & ControlMODULE TUTOR: Dr. Ahmed OnsySEMESTER 2, 2019/20Submission Date and Time:11:59 pm, 10th April, 2020Venue/Campus: PRESTON CAMPUSName ………………………………………………………………2 of4Sensors, Instrumentation & Control, MP4706 – Assessment 1 2019/20Instructions to Candidates:ValueThis assignment constitutes 50% of the grade for this module.Submission Date and Time:11:59 pm, 10th April, 2020Submission RulesThe assignment should be your own work and written in your own words. It will be checkedfor similarity using Turnitin. Any plagiarism or copying from others will be dealt with throughthe university’s plagiarism procedures.Your assignment must be submitted electronically via BlackBoard (Assignments tab) by thesubmission time and date. The report should be contained in a Word document, or PDF Noother means of submission will be accepted. The software code will be submittedindependently.Any assignment submitted late, but within 5 working days of the deadline, will be given amaximum mark of 50%. Assignments submitted more than 5 working days after the deadlinewill not be marked, and a mark of 0% will be recorded.Learning Outcome to be assessed:
1
Demonstrate knowledge and critical understanding of sensors and transducerstypically encountered in engineering applications
2
Understand critically the practical aspects of sensor use and type
3
Demonstrate knowledge and critical understanding of the principles ofinstrumentation and measurement systems
4
Demonstrate knowledge and critical understanding in the devise of anappropriate and effective strategy for processing data; virtual instrumentationand virtual simulation
3 of4Sensors, Instrumentation & Control, MP4706 – Assessment 1 2019/20Task:‘Global-Technologies’, is a systemengineering company that developsmeasurement systems for different industriesto support a wide range of applications.You have been asked as an engineer in the
‘Global- Technologies’ company, to designand develop a measurement system that isable to demonstrate the operation of crane‘Load Moment Indicator’ (LMI) system using
Source: http://www.basilcranes.com/
sensors model. The measurement systemincludes the measurement of crane boomlength, boom angle, load, outrigger position,and driver cabinet temperature.Provide a detailed, professional report foryour director that contains the following:1- A review of different LMI systems usedin cranes industry including their mainelements.2- A design of a typical LMI system that incorporates the measurement of craneparameters including boom length, boom angle, load, outriggers position, andtemperature. The system design should include DAQ/ microcontroller and anyother required elements for a typical LMI system.3- A measurement software program (LabVIEW/ C++) that can be used to providethe following parameters, log the measurement data, and give warning alarmswhen limits of the following parameters are exceeded.➢ Boom length➢ Outriggers position➢ Load➢ Driver cabinet temperature4- Experimental results and critical analysis that evaluate two sensors of the LMIsystem using the NI DAQ and NI LabVIEW software.5- An evaluation of signal conditioning elements that are required to measure theload using strain gauges.6- Proposal for the next phases of development to include the following:A. Using of a low-cost controller instead of the current oneB. Other methods of data transmissions; wireless or wired data transmission,and use of the Internet of Things
4 of4Assessment CriteriaThe Department’s Principles of Assessment will be used to determine grading levels.
1
A review of different LMI systems used in cranes including their mainelements.
20%
2
A design of a typical LMI system that incorporates the measurementof crane parameters including boom length, boom angle, load,outriggers position, and temperature of the driver cabinet. The systemdesign should include DAQ/ controller and any other requiredelements for a typical LMI system.
10%
3
A measurement software program (LabVIEW/ C++) that can be usedto provide the following parameters, log the measurement data, andgive warning alarms when limits of the following parameters areexceeded; boom length, outriggers position, temperature and load
20%
4
Experimental results and critical analysis that evaluate two sensors ofthe LMI system using the NI DAQ and NI LabVIEW software.
10%
5
An evaluation of signal conditioning elements that are required tomeasure the load using strain gauges.
10%
6 – A
Proposal for the next phases of development to include the use of alow-cost controller instead of the current one.
10%
6 – B
Proposal for the next phases of development to include the use ofother methods of data transmissions; wireless or wired datatransmission, and Internet of Things.
10%
7
Report presentation, structure, clarify of information, use ofreferences.
10%

READ ALSO  Dining Philosophers AssignmentTutorOnlineTicTacToe AssignmentTutorOnline | Good Grade Guarantee!

QUALITY: 100% ORIGINAL – NO PLAGIARISM.

  • **REMEMBER TO PRECISE PAGE NUMBER**
  • Hit The Order Button To Order A **Custom Paper**

>> 100% ORIGINAL PAPERS FROM AustralianExpertWriters.com <<